高壓泵報警 ：

　　High pressure pump alarm:

　　過載 ：使用過長時間或清洗工作負荷過大，可能導致高壓泵過載。

　　Overload: Prolonged use or excessive cleaning workload may cause the high-pressure pump to overload.

　　泄漏 ：泵的密封部分可能出現泄漏，導致壓力不穩定。

　　Leakage: The sealing part of the pump may leak, causing unstable pressure.

　　油液問題 ：油液溫度過高或油液質量不合格都可能導致高壓泵報警。定期更換油液和維護油液冷卻系統可以這個問題。

　　Oil problem: High oil temperature or poor oil quality may cause the high-pressure pump to alarm. Regularly replacing the oil and maintaining the oil cooling system can solve this problem.

　　電機故障 ：電機故障也可能導致高壓泵報警，需要檢查電機狀態并修復故障。

　　Motor failure: Motor failure may also cause the high-pressure pump to alarm, and it is necessary to check the motor status and repair the fault.

　　水泵報警 ：

　　Pump alarm:

　　水源問題 ：水泵需要足夠的水源供應，如果水源不足或水管堵塞，會導致水泵報警。

　　Water source issue: The water pump requires sufficient water supply. If the water source is insufficient or the water pipe is blocked, it will cause the water pump to alarm.

　　過載或過熱 ：過長時間的高強度使用或水泵過熱可能導致報警。需要適當控制使用時間和強度。

　　Overload or overheating: Prolonged high-intensity use or overheating of the water pump may cause an alarm. It is necessary to control the usage time and intensity appropriately.

　　水泵損壞 ：水泵部件磨損或損壞可能導致報警，需要檢查和更換受損部分。

　　Water pump damage: Wear or damage to water pump components may cause an alarm, and the damaged parts need to be inspected and replaced.

　　溫度報警 ：

　　Temperature alarm:

　　電機或液壓系統溫度過高 ：這可能是由于工作環境溫度過高、油液問題或冷卻系統故障引起的。需要確保工作環境通風良好，維護液壓系統并檢查冷卻系統的狀態。

　　Motor or hydraulic system temperature too high: This may be caused by high working environment temperature, oil problems, or cooling system failures. It is necessary to ensure good ventilation in the working environment, maintain the hydraulic system, and check the status of the cooling system.

　　泄漏報警 ：

　　Leakage alarm:

　　液壓系統或密封部分泄漏 ：這可能是由于密封件老化、損壞或不合格引起的。需要定期檢查并更換受損的密封件。

　　Leakage in hydraulic system or sealing parts: This may be caused by aging, damage, or non-compliance of seals. Regular inspection and replacement of damaged seals are required.

　　高壓線路故障 ：

　　High voltage line fault:

　　高壓泵與電控箱傳感器故障 ：傳感器失靈。

　　High pressure pump and electrical control box sensor malfunction: Sensor failure.

　　電控箱與電源連接不穩 ：接觸不良。

　　Unstable connection between the electrical control box and the power supply: poor contact.

　　清洗機電控故障 ：

　　Cleaning machine electrical control malfunction:

　　控制開關失靈或損壞 ：需要檢查控制箱內。

　　Control switch malfunction or damage: It is necessary to check the control box.

　　根據以上原因，可以逐一排查高壓清洗機的報警問題，并采取相應的措施。建議定期對高壓清洗機進行維護和檢查，以確保其正常運行和延長使用壽命。

　　Based on the above reasons, the alarm problems of the high-pressure cleaning machine can be investigated one by one, and corresponding solutions can be taken. It is recommended to regularly maintain and inspect the high-pressure cleaning machine to ensure its normal operation and extend its service life.

　　本文CNC高壓清洗機由提供幫助，更多的相關內容請點擊：http://www.rllrhm.com希望本文能夠為您帶來幫助，感謝您的閱讀！

　　This article provides assistance for CNC high-pressure cleaning machines. For more related content, please click: http://www.rllrhm.com I hope this article can be helpful to you. Thank you for reading!