除了做好CNC高壓清洗機的日常維護和保養外，對于平時會出現的一些小問題，我們也要學會排查，下面就跟大家分析下關于CNC高壓清洗機出水壓力不足的原因和處理方法有哪幾種。

In addition to the daily maintenance of the CNC high-pressure washer, we should also learn to troubleshoot some small problems that usually occur. Now we will analyze the causes and treatment methods of the insufficient water pressure of the CNC high-pressure washer.

1.CNC高壓清洗機高壓噴嘴出現嚴重磨損，高壓噴嘴磨損過度會影響設備的出水壓力，應及時的去更換新的噴嘴。

1. The high pressure nozzle of CNC high pressure washer is seriously worn, and excessive wear of the high pressure nozzle will affect the water outlet pressure of the equipment, so it should be replaced in time.

2.接入設備的進水流量不足導致水流量不足，從而輸出壓力不足。應及時供應足夠進水流量，即可出水壓力降低的問題。

2. Inadequate water inflow to the equipment leads to insufficient water flow, resulting in insufficient output pressure. The problem of water outlet pressure reduction can be solved by timely supplying sufficient water inlet flow.

3.CNC高壓清洗機清潔進水過濾器有空氣，應排盡清潔進水過濾器內的空氣后，確保輸出標準的出水壓力。

3. There is air in the clean water inlet filter of CNC high-pressure washer. After the air in the clean water inlet filter is exhausted, ensure that the standard water outlet pressure is output.

4.CNC高壓清洗機溢流閥老化后，造成水流溢流量大，壓力變低，當發現其老化時就要及時更換配件。

4. After the aging of the overflow valve of the CNC high-pressure washer, the overflow flow of water will be large and the pressure will become low. When it is found that it is aging, it is necessary to replace the parts in time.

5.CNC高壓清洗機高低壓水封和進出水單向閥出現泄漏現象導致工作壓力變低，應及時更換這些配件。

5. In case of leakage of high and low pressure water seal and inlet and outlet one-way valve of CNC high-pressure washer, which leads to low working pressure, these accessories shall be replaced in time.

6.高壓管、過濾裝置扭結、彎折或者損壞，導致水流流通不暢，導致出水壓力不足，應及時修復。

6. The high pressure pipe and filter device are twisted, bent or damaged, resulting in poor water flow and insufficient outlet pressure, which shall be repaired in time.

7.高壓泵內部出現故障，易損件磨損，水流量降低;設備內部管路出現堵塞，水流量太小，導致工作壓力過低。

7. High pressure pump has internal failure, wearing parts are worn, and water flow is reduced; The pipeline inside the equipment is blocked and the water flow is too small, resulting in low working pressure.

好的清潔設備應該懂得及時的保養與維護，提高清潔設備的使用壽命，減低清潔成本支出。更多相關內容的了解就來我們網站www.rllrhm.com咨詢吧！

Good cleaning equipment should know how to timely maintain, improve the service life of cleaning equipment, and reduce cleaning costs. For more information, please visit our website www.rllrhm.com!